Are you confused about “how to control addressable LED strip with Arduino”?
Addressable LED light strips are an advanced lighting solution, with built-in ICs that allow each LED to be individually controlled. Arduino, as a controller, can be combined with addressable LED light strips to achieve personalized lighting effects, high cost-effectiveness, and intelligent lighting control.
The combination of addressable LED light strips and Arduino is becoming increasingly popular in lighting projects, and this trend is not without reason.
If you want to learn more about how to control WS2812 LED strips with Raspberry Pi, check out this article.
What Is The Addressable LED Strip?
As is well known, an LED light strip is a lighting device. More precisely, it is a continuous lighting source formed by assembling many light-emitting diodes (LEDs) on a slender plate-shaped or cylindrical carrier.
So, what is an addressable LED strip?
The addressable LED strip is a special LED lighting product with IC. As the name suggests, addressable LED light strips refer to each LED bead on the light strip having an independent address, which can be individually controlled by a specific controller or programming method for each LED bead.
Addressable LED strips have signal propagation directions. You will see arrows marking the direction of propagation on its PCB. Be sure not to connect in the opposite direction of signal propagation, otherwise the strip will be damaged.
If you want to know more about what is addressable LED strip? How to choose an addressable LED strip, please click our other blog How To Choose The Right Addressable LED Strip.
Click To Enlarge
Click To Enlarge
Addressable RGB LED Strip
SMD RGB LED strip without IC
After understanding the concept of addressable LED light strips, what is a non-addressable LED strip?
Since each LED bead on an addressable LED strip has an independent address and can be controlled separately, a continuous lighting source composed of multiple LED beads connected in series or parallel that cannot be controlled separately is a non-addressable LED light strip.
Non-addressable LED strips usually don’t have an IC. Or you can understand it as just one IC and all LEDs light up or turn off or change the same way at the same time.
The LED beads on it are usually controlled uniformly, which means they will light up or turn off simultaneously. Non-addressable LED strips are also commonly referred to as SMD LED strips. This type of light strip generally has no direction of signal propagation.
Based on the above explanation of the concepts of addressable and non addressable LED light strips, I have summarized the differences between the two, as shown in the table below.
Addressable LED Strip Vs. Non-addressable LED Strip
| Control Mode | Function | Application | Technical Realization |
|---|---|---|---|
| Addressable | Each LED bead can be individually controlled | Stage lighting, entertainment venues, smart city projects | Digital protocols (DMX512/SPI) |
| Non-addressable | Uniform control of LED beads | Home/office lighting, simple displays | Basic circuit control |
Why Use an Arduino?
There are many ways to control addressable LED light strips, such as Arduino control, microcontroller control, DMX512 control, Wi-Fi control, Bluetooth control, etc. From the perspective of universality and progressiveness, the control mode of digital communication protocol (such as DALI, DMX512, etc.) combined with microcontroller Arduino has significant advantages.
The Arduino platform not only provides a large number of open-source libraries but also achieves separation from hardware through code encapsulation, greatly improving development efficiency; It can also flexibly and accurately control each LED, supporting multiple communication protocols; Not only that, the success of Arduino development boards is relatively low and easy to purchase.
At the same time, the programming environment of Arduino is based on C++ but has been simplified and packaged, making it easy for even users without programming experience to get started quickly.
Wiring the WS2812B Addressable LED Strip With Arduino
Next, let’s start using Arduino to light up the WS2812B addressable LED strip, achieving single control and rainbow running light effects.
For detailed steps, you can refer to the video below. If you want to understand it as quickly as possible in text form, please read the text description below.
Tools and Components Required
Firstly, it is necessary to prepare the necessary tools and components:
- Arduino Uno
- WS2812B light strip (24 lights)
- Several jumper wires (Duban wires)
- FastLED Library
Step-by-Step Guide Wiring WS2812B Addressable LED Strip With Arduino
I will use a WS2812B light strip (24 lights) connected to Arduino through several wires and powered by a 5V power supply.
Before that, we need to install the FastLED library. The FastLED library can be installed and used by searching for “FastLED” in the “Library Management” section of the Arduino IDE.
In addition to writing LEDs, the library also includes many high-performance 8-bit mathematical functions for processing RGB values, as well as low-level classes for abstracting access to pins and SPI hardware.
The wiring method is shown in figure below.
Explanation: This example program is applicable to WS2812 LED strips with 3 wires (power line, ground line, data line).
Firstly, we need to define the number of LEDs, IO 3 of the development board as the data pin, and arrays of CRGB LEDs. Set the LED with index 0 to white and light it up, which is the first LED flashing white.
After turning off the first LED, we will flash each LED green one by one. Using the HSV color space, we will continuously change the value of H.
To update the LED status, we need to call FastLED. show(). Finally, the entire LED strip will present a rainbow color gradient effect.
For more connection and wiring examples across different addressable LED strip types, see our guide to controlling, connecting and wiring addressable LED strips.
Program Code:
// This example program is suitable for 3-wire (power, ground, data) WS2812 LED strips
#include
#define NUM_LEDS 24 // Define the number of LEDs
#define DATA_PIN 3 // Define pin 3 of the board as the data pin
CRGB leds[NUM_LEDS]; // Define an array of CRGB LEDs
void setup() {
FastLED.addLeds(leds, NUM_LEDS);
}
void loop() {
// The first LED blinks white
leds[0] = CRGB::White; // Set LED with index 0 to white (turn on)
FastLED.show();
delay(500);
leds[0] = CRGB::Black; // Set LED with index 0 to black (turn off)
FastLED.show();
delay(500);
delay(500);
// Each LED blinks green one by one
for(int i = 0; i < NUM_LEDS; i++ ) {
leds[i] = CRGB::Green;
FastLED.show();
delay(100);
leds[i] = CRGB::Black;
FastLED.show();
delay(100);
}
delay(1000);
// The entire LED strip fades in a rainbow pattern
int h = 0;
for(int j = 0; j < 255; j++) {
for (int i = 0; i < NUM_LEDS; i++) {
leds[i] = CHSV( (h + (255 / NUM_LEDS) * i), 255, 255); // Use HSV color space and continuously change the hue
FastLED.show();
}
delay(1);
h = (h + 2) % 255;
}
// Turn off the entire LED strip
for(int i = 0; i < NUM_LEDS; i++ ){
leds[i] = CRGB::Black;
}
FastLED.show();
delay(1000);
}
That concludes this article. If you have already completed your LED lighting project or are looking for inspiration and suggestions, please feel free to leave a comment or share your work on social media.
Let’s communicate and learn together, and explore the infinite possibilities brought by Arduino controlled addressable LED light strips! Your creativity and passion will inspire more people to join this fun and challenging field.
FAQ
How Do You Control an Addressable LED Strip with Arduino?
You can control compatible addressable LED strips with Arduino by sending digital data through a microcontroller pin. This guide uses a WS2812B strip and the FastLED library to create individual colors, blinking patterns, and rainbow effects.
How Do You Connect a WS2812B LED Strip to Arduino?
For the WS2812B example, connect Arduino data pin 3 to the strip’s data input, and connect grounds together. Power the strip from a suitable external supply rather than relying on the Arduino board’s output alone for power.
Is FastLED or Adafruit NeoPixel Better for Arduino LED Strips?
FastLED is a suitable choice for the article’s WS2812B example because it supports color arrays and animation effects. Adafruit NeoPixel is another option, especially for straightforward projects; library choice depends on the chip and code requirements.
Why Is My Addressable LED Strip Not Lighting Up with Arduino?
If an addressable strip does not light, first verify the strip’s input direction, data-pin assignment, LED count in the code, and common ground. Then confirm the supply voltage matches the strip and inspect connections before replacing components.